3.4.6 Lab – Configure VLANs and Trunking Answers

3.4.6 Lab – Configure VLANs and Trunking Answers

Lab – Configure VLANs and Trunking (Answers Version)

Answers Note: Red font color or gray highlights indicate text that appears in the Answers copy only.

Topology

This topology has 2 PCs and 2 switches. PC-A is connected S1 F0/6. S1 F0/1 is connected to S2 F0/1. Pc-B is connected to S2 F0/18.

Addressing Table

Device

Interface

IP Address

Subnet Mask

Default Gateway

S1

VLAN 1

192.168.1.11

255.255.255.0

N/A

S2

VLAN 1

192.168.1.12

255.255.255.0

N/A

PC-A

NIC

192.168.10.3

255.255.255.0

192.168.10.1

PC-B

NIC

192.168.10.4

255.255.255.0

192.168.10.1

Objectives

Part 1: Build the Network and Configure Basic Device Settings

Part 2: Create VLANs and Assign Switch Ports

Part 3: Maintain VLAN Port Assignments and the VLAN Database

Part 4: Configure an 802.1Q Trunk between the Switches

Part 5: Delete the VLAN Database

Background / Scenario

Modern switches use virtual local-area networks (VLANs) to improve network performance by separating large Layer 2 broadcast domains into smaller ones. VLANs can also be used as a security measure by controlling which hosts can communicate. In general, VLANs make it easier to design a network to support the goals of an organization.

VLAN trunks are used to span VLANs across multiple devices. Trunks allow the traffic from multiple VLANS to travel over a single link, while keeping the VLAN identification and segmentation intact.

In this lab, you will create VLANs on both switches in the topology, assign VLANs to switch access ports, verify that VLANs are working as expected, and then create a VLAN trunk between the two switches to allow hosts in the same VLAN to communicate through the trunk, regardless of which switch the host is actually attached to.

Note: The switches used with CCNA hands-on labs are Cisco Catalyst 2960s with Cisco IOS Release 15.2(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.

Note: Ensure that the routers and switches have been erased and have no startup configurations. If you are unsure contact your Answers.

Answers Note: Refer to the Answers Lab Manual for the procedures to initialize and reload devices.

Required Resources

  • 2 Switches (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable)
  • 2 PCs (Windows with a terminal emulation program, such as Tera Term)
  • Console cables to configure the Cisco IOS devices via the console ports
  • Ethernet cables as shown in the topology

Instructions

Part 1:  Build the Network and Configure Basic Device Settings

In Part 1, you will set up the network topology and configure basic settings on the PC hosts and switches.

Step 1:  Cable the network as shown in the topology.

Attach the devices as shown in the topology diagram, and cable as necessary.

Step 2:  Configure basic settings for each switch.

  1. Console into the switch and enable privileged EXEC mode.

Open configuration window

switch> enable

  1. Enter configuration mode.

switch# config terminal

  1. Assign a device name to the switch.

switch(config)# hostname S1

 

switch(config)# hostname S2

  1. Disable DNS lookup to prevent the router from attempting to translate incorrectly entered commands as though they were host names.

S1(config)# no ip domain-lookup

 

S2(config)# no ip domain-lookup

  1. Assign class as the privileged EXEC encrypted password.

S1(config)# enable secret class

 

S2(config)# enable secret class

  1. Assign cisco as the console password and enable login.

S1(config)# line console 0

S1(config-line)# password cisco

S1(config-line)# login

 

S2(config)# line console 0

S2(config-line)# password cisco

S2(config-line)# login

  1. Assign cisco as the vty password and enable login.

S1(config)# line vty 0 4

S1(config-line)# password cisco

S1(config-line)# login

 

S2(config)# line vty 0 4

S2(config-line)# password cisco

S2(config-line)# login

  1. Encrypt the plaintext passwords.

S1(config)# service password-encryption

 

S2(config)# service password-encryption

  1. Create a banner that warns anyone accessing the device that unauthorized access is prohibited.

S1(config)# banner motd $ Authorized Users Only! $

 

S2(config)# banner motd $ Authorized Users Only! $

  1. Configure the IP address listed in the Addressing Table for VLAN 1 on the switch.

S1(config)# interface vlan 1

S1(config-if)# ip address 192.168.1.11 255.255.255.0

S1(config-if)# no shutdown

S1(config-if)# exit

 

S2(config)# interface vlan 1

S2(config-if)# ip address 192.168.1.12 255.255.255.0

S2(config-if)# no shutdown

S2(config-if)# exit

  1. Shut down all interfaces that will not be used.

S1(config)# interface range f0/2-5, f0/7-24, g0/1-2

S1(config-if-range)# shutdown

 

S2(config)# interface range f0/2-17, f0/18-24, g0/1-2

S2(config-if-range)# shutdown

  1. Set the clock on the switch.

S1# clock set 15:30:00 19 September 2019

 

S2# clock set 15:30:00 19 September 2019

  1. Save the running configuration to the startup configuration file.

S1# copy running-config startup-config

 

S2# copy running-config startup-config

Close configuration window

Step 3:  Configure PC hosts.

Refer to the Addressing Table for PC host address information.

Step 4:  Test connectivity.

Verify that the PC hosts can ping one another.

Note: It may be necessary to disable the PCs firewall to ping between PCs.

Questions:

Can PC-A ping PC-B?

Yes

Can PC-A ping S1?

No

Can PC-B ping S2?

No

Open configuration window

Can S1 ping S2?

Yes

If you answered no to any of the above questions, why were the pings unsuccessful?

Pings were unsuccessful when trying to ping a device on a different subnet. For those pings to be successful, a default gateway must exist to route traffic from one subnet to another.

Close configuration window

Part 2:  Create VLANs and Assign Switch Ports

In Part 2, you will create Management, Operations, Parking_Lot, and Native VLANs on both switches. You will then assign the VLANs to the appropriate interface. The show vlan command is used to verify your configuration settings.

Step 1:  Create VLANs on the switches.

Open configuration window

  1. Create the VLANs on S1.

S1(config)# vlan 10

S1(config-vlan)# name Operations

S1(config-vlan)# vlan 20

S1(config-vlan)# name Parking_Lot

S1(config-vlan)# vlan 99

S1(config-vlan)# name Management

S1(config-vlan)# vlan 1000

S1(config-vlan)# name Native

S1(config-vlan)# end

  1. Create the same VLANs on S2.
  2. Issue the show vlan brief command to view the list of VLANs on S1.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8

                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12

                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16

                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20

                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24

                                                Gi0/1, Gi0/2

10   Operations                       active

20   Parking_Lot                      active

99   Management                       active

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Questions:

What is the default VLAN?

VLAN 1

What ports are assigned to the default VLAN?

All switch ports are assigned to VLAN 1 by default.

Step 2:  Assign VLANs to the correct switch interfaces.

  1. Assign VLANs to the interfaces on S1.

1)      Assign PC-A to the Operation VLAN.

S1(config)# interface f0/6

S1(config-if)# switchport mode access

S1(config-if)# switchport access vlan 10

2)      Move the switch IP address VLAN 99.

S1(config)# interface vlan 1

S1(config-if)# no ip address

S1(config-if)# interface vlan 99

S1(config-if)# ip address 192.168.1.11 255.255.255.0

S1(configif)# end

  1. Issue the show vlan brief command and verify that the VLANs are assigned to the correct interfaces.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Fa0/11, Fa0/12, Fa0/13

                                                Fa0/14, Fa0/15, Fa0/16, Fa0/17

                                                Fa0/18, Fa0/19, Fa0/20, Fa0/21

                                                Fa0/22, Fa0/23, Fa0/24, Gi0/1

                                                Gi0/2

10   Operations                       active    Fa0/6

20   Faculty                          active   

99   Management                       active   

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

  1. Issue the show ip interface brief command.

S1# show ip interface brief

Interface              IP-Address      OK? Method Status                Protocol

Vlan1                  unassigned      YES unset  up                    up     

Vlan99                 192.168.1.11    YES manual up                    down   

FastEthernet0/1        unassigned      YES unset  up                    up     

FastEthernet0/2        unassigned      YES unset  administratively down down   

FastEthernet0/3        unassigned      YES unset  administratively down down   

FastEthernet0/4        unassigned      YES unset  administratively down down   

FastEthernet0/5        unassigned      YES unset  administratively down down   

FastEthernet0/6        unassigned      YES unset  up                    up     

FastEthernet0/7        unassigned      YES unset  administratively down down   

<output omitted>

Question:

What is the status of VLAN 99? Explain.

The status of VLAN 99 is up/down, up because the VLAN exists in the database but down because the VLAN has not been assigned to an active port yet.

  1. Assign PC-B to the Operations VLAN on S2.

S2(config)# interface f0/18

S2(config-if)# switchport mode access

S2(config-if)# switchport access vlan 10

  1. Remove the IP address for VLAN 1 on S2.

S2(config)# interface vlan 1

S2(config-if)# no ip address

  1. Configure an IP address for VLAN 99 on S2 according to the Addressing Table.

S2(configif)# interface vlan 99

S2(config-if)# ip address 192.168.1.12 255.255.255.0

  1. Use the show vlan brief command to verify that the VLANs are assigned to the correct interfaces.

S2# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8

                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12

                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16

                                                Fa0/17, Fa0/19, Fa0/20, Fa0/21

                                                Fa0/22, Fa0/23, Fa0/24, Gi0/1

                                                Gi0/2

10   Operations                       active    Fa0/18

20   Parking_Lot                      active

99   Management                       active

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Questions:

Is S1 able to ping S2? Explain.

No. The IP addresses for the switches now reside in VLAN 99. VLAN 99 traffic will not be sent over interface F0/1.

Close configuration window

Is PC-A able to ping PC-B? Explain.

No. Interface F0/1 is not assigned to VLAN 10, so VLAN 10 traffic will not be sent over it.

Part 3:  Maintain VLAN Port Assignments and the VLAN Database

In Part 3, you will change VLAN assignments to ports and remove VLANs from the VLAN database.

Step 1:  Assign a VLAN to multiple interfaces.

Open configuration window

  1. On S1, assign interfaces F0/11 – 24 to VLAN99.

S1(config)# interface range f0/11-24

S1(config-ifrange)# switchport mode access

S1(config-ifrange)# switchport access vlan 99

S1(config-ifrange)# end

  1. Issue the show vlan brief command to verify VLAN assignments.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6

20   Parking_Lot                      active

99   Management                       active    Fa0/11, Fa0/12, Fa0/13, Fa0/14

                                                Fa0/15, Fa0/16, Fa0/17, Fa0/18

                                                Fa0/19, Fa0/20, Fa0/21, Fa0/22

                                                Fa0/23, Fa0/24

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

  1. Reassign F0/11 and F0/21 to VLAN 10.

S1(config)# interface range f0/11, f0/21

S1(config-ifrange)# switchport access vlan 10

S1(config-ifrange)# end

  1. Verify that VLAN assignments are correct.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23, Fa0/24

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Step 2:  Remove a VLAN assignment from an interface.

  1. Use the no switchport access vlan command to remove the VLAN 99 assignment to F0/24.

S1(config)# interface f0/24

S1(config-if)# no switchport access vlan

S1(config-if)# end

  1. Verify that the VLAN change was made.

Question:

Which VLAN is F0/24 now associated with?

VLAN 1, the default VLAN.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Fa0/24, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Step 3:  Remove a VLAN ID from the VLAN database.

  1. Add VLAN 30 to interface F0/24 without issuing the global VLAN command.

S1(config)# interface f0/24

S1(config-if)# switchport access vlan 30

% Access VLAN does not exist. Creating vlan 30

Note: Current switch technology no longer requires that the vlan command be issued to add a VLAN to the database. By assigning an unknown VLAN to a port, the VLAN will be created and added to the VLAN database.

  1. Verify that the new VLAN is displayed in the VLAN table.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

30   VLAN0030                         active    Fa0/24

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Question:

What is the default name of VLAN 30?

VLAN0030

  1. Use the no vlan 30 command to remove VLAN 30 from the VLAN database.

S1(config)# no vlan 30

S1(config)# end

  1. Issue the show vlan brief command. F0/24 was assigned to VLAN 30.

Question:

After deleting VLAN 30 from the VLAN database, what VLAN is port F0/24 assigned to? What happens to the traffic destined to the host attached to F0/24?

When you delete a VLAN, any ports assigned to that VLAN become inactive. So Port F0/24 is still -associated to VLAN 30. However, VLAN 30 is now inactive because it does not exist in the VLAN database. Additionally, the port will not transfer any traffic.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

  1. Issue the no switchport access vlan command on interface F0/24.

S1(config)# interface f0/24

S1(config-if)# no switchport access vlan

S1(config-if)# end

  1. Issue the show vlan brief command to determine the VLAN assignment for F0/24.

Questions:

To which VLAN is F0/24 assigned?

The default VLAN, VLAN 1

S1# show vlan brief

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4

                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9

                                                Fa0/10, Fa0/24, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Note: Before removing a VLAN from the database, it is recommended that you reassign all the ports assigned to that VLAN.

Why should you reassign a port to another VLAN before removing the VLAN from the VLAN database?

The interfaces assigned to a VLAN that is the removed from the VLAN database become inactive and are unavailable for use until they are reassigned to another VLAN. This can be a tricky thing to troubleshoot as trunked interfaces do not show up in the port list as well (Part 4 contains more information about trunked interfaces).

Close configuration window

Part 4:  Configure an 802.1Q Trunk Between the Switches

In Part 4, you will configure interface F0/1 to use the Dynamic Trunking Protocol (DTP) to allow it to negotiate the trunk mode. After this has been accomplished and verified, you will disable DTP on interface F0/1 and manually configure it as a trunk.

Step 1:  Use DTP to initiate trunking on F0/1.

The default DTP mode of a 2960 switch port is dynamic auto. This allows the interface to convert the link to a trunk if the neighboring interface is set to trunk or dynamic desirable mode.

Open configuration window

  1. Set F0/1 on S1 to negotiate trunk mode.

S1(config)# interface f0/1

S1(config-if)# switchport mode dynamic desirable

Sep 19 02:51:47.257: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Sep 19 02:51:47.291: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan99, changed state to up

You should also receive link status messages on S2.

S2#

Sep 19 02:42:19.424: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

Sep 19 02:42:21.454: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan99, changed state to up

Sep 19 02:42:22.419: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

  1. Issue the show vlan brief command on S1 and S2. Interface F0/1 is no longer assigned to VLAN 1. Trunked interfaces are not listed in the VLAN table.

S1# show vlan brief

 

VLAN Name                             Status    Ports

—- ——————————– ——— ——————————-

1    default                          active    Fa0/2, Fa0/3, Fa0/4, Fa0/5

                                                Fa0/7, Fa0/8, Fa0/9, Fa0/10

                                                Fa0/24, Gi0/1, Gi0/2

10   Operations                       active    Fa0/6, Fa0/11, Fa0/21

20   Parking_Lot                      active

99   Management                       active    Fa0/12, Fa0/13, Fa0/14, Fa0/15

                                                Fa0/16, Fa0/17, Fa0/18, Fa0/19

                                                Fa0/20, Fa0/22, Fa0/23

1000 Native                           active

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

  1. Issue the show interfaces trunk command to view trunked interfaces. Notice that the mode on S1 is set to desirable, and the mode on S2 is set to auto.

S1# show interfaces trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       desirable        802.1q         trunking      1

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,20,99,1000

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,20,99,1000

 

S2# show interfaces trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       auto             802.1q         trunking      1

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,20,99,1000

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,20,99,1000

Note: By default, all VLANs are allowed on a trunk. The switchport trunk command allows you to control what VLANs have access to the trunk. For this lab, keep the default settings which allows all VLANs to traverse F0/1.

Close configuration window

  1. Verify that VLAN traffic is traveling over trunk interface F0/1.

Questions:

Can S1 ping S2?

Yes

Can PC-A ping PC-B?

Yes

Can PC-A ping S1?

No

Can PC-B ping S2?

No

If you answered no to any of the above questions, explain below.

The switches are in VLAN 99 and the PCs are in VLAN 10; therefore, the pings between VLANs were unsuccessful.

Step 2:  Manually configure trunk interface F0/1.

The switchport mode trunk command is used to manually configure a port as a trunk. This command should be issued on both ends of the link.

  1. Change the switchport mode on interface F0/1 to force trunking. Make sure to do this on both switches.

Open configuration window

S1(config)# interface f0/1

S1(config-if)# switchport mode trunk

 

S2(config)# interface f0/1

S2(config-if)# switchport mode trunk

  1. Issue the show interfaces trunk command to view the trunk mode. Notice that the mode changed from desirable to on.

S2# show interfaces trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       on               802.1q         trunking      1

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,20,99,1000

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,20,99,1000

  1. Modify the trunk configuration on both switches by changing the native VLAN from VLAN 1 to VLAN 1000.

S1(config)# interface f0/1

S1(config-if)# switchport trunk native vlan 1000

 

S2(config)# interface f0/1

S2(config-if)# switchport trunk native vlan 1000

  1. Issue the show interfaces trunk command to view the trunk. Notice the Native VLAN information is updated.

S2# show interfaces trunk

 

Port        Mode             Encapsulation  Status        Native vlan

Fa0/1       on               802.1q         trunking      1000

 

Port        Vlans allowed on trunk

Fa0/1       1-4094

 

Port        Vlans allowed and active in management domain

Fa0/1       1,10,20,99,1000

 

Port        Vlans in spanning tree forwarding state and not pruned

Fa0/1       1,10,20,99,1000

Questions:

Why might you want to manually configure an interface to trunk mode instead of using DTP?

Not all equipment uses DTP. Using the switchport mode trunk command ensures that the port will become a trunk no matter what type of equipment is connected to the other end of the link.

Why might you want to change the native VLAN on a trunk?

Using VLAN 1, the default VLAN, as the native VLAN is a security risk. All the different control protocols that are exchanged between switches are exchanged via the native VLAN 1 untagged, and that information could be exposed if default settings are used on ports that users connect to.

Close configuration window

Part 5:  Delete the VLAN Database

In Part 5, you will delete the VLAN Database from the switch. It is necessary to do this when initializing a switch back to its default settings.

Step 1:  Determine if the VLAN database exists.

Open configuration window

Issue the show flash command to determine if a vlan.dat file exists in flash.

S1# show flash:

 

Directory of flash:/

 

    2  rwx       59416   Mar 1 1993 01:20:12 +00:00  multiple-fs

    3  rwx    15186645   Mar 1 1993 00:19:23 +00:00  c2960-lanbasek9-mz.152-4.E8.bin

    5  rwx         796  Sep 19 2019 02:48:04 +00:00  vlan.dat

 

61028352 bytes total (33762304 bytes free)

Note: If there is a vlan.dat file located in flash, then the VLAN database does not contain its default settings.

Step 2:  Delete the VLAN database.

  1. Issue the delete vlan.dat command to delete the vlan.dat file from flash and reset the VLAN database back to its default settings. You will be prompted twice to confirm that you want to delete the vlan.dat file. Press Enter both times.

S1# delete vlan.dat

Delete filename [vlan.dat]?

Delete flash:/vlan.dat? [confirm]

  1. Issue the show flash command to verify that the vlan.dat file has been deleted.

S1# show flash:

 

Directory of flash:/

 

    2  rwx       59416   Mar 1 1993 01:20:12 +00:00  multiple-fs

    3  rwx    15186645   Mar 1 1993 00:19:23 +00:00  c2960-lanbasek9-mz.152-4.E8.bin

 

61028352 bytes total (33763840 bytes free)

Question:

To initialize a switch back to its default settings, what other commands are needed?

To get a switch back to its default settings, the erase startup-config and reload commands need to be issued after the delete vlan.dat command.

Close configuration window

Reflection Questions

  1. What is needed to allow hosts on VLAN 10 to communicate to hosts on VLAN 99?

Answers will vary, but to allow Inter-VLAN routing requires a Layer 3 device is needed to route traffic between VLANs.

  1. What are some primary benefits that an organization can receive through effective use of VLANs?

Answers will vary, but VLAN benefits include: better security, cost savings (efficient use of bandwidth and uplinks), higher performance (smaller broadcast domains), broadcast storm mitigation, improved IT staff efficiency, simpler project and application management.

End of Document

Device Configs – Final

Switch S1

Building configuration…

 

Current configuration : 2571 bytes

!

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname S1

!

boot-start-marker

boot-end-marker

!

enable secret 5 $1$GCQG$N33u/asvJfEWsnrIHRWjM1

!

no aaa new-model

system mtu routing 1500

!

no ip domain-lookup

!

spanning-tree mode pvst

spanning-tree extend system-id

!

vlan internal allocation policy ascending

!

interface FastEthernet0/1

 switchport trunk native vlan 1000

 switchport mode trunk

!

interface FastEthernet0/2

 shutdown

!

interface FastEthernet0/3

 shutdown

!

interface FastEthernet0/4

 shutdown

!

interface FastEthernet0/5

 shutdown

!

interface FastEthernet0/6

 switchport access vlan 10

 switchport mode access

!

interface FastEthernet0/7

 shutdown

!

interface FastEthernet0/8

 shutdown

!

interface FastEthernet0/9

 shutdown

!

interface FastEthernet0/10

 shutdown

!

interface FastEthernet0/11

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/12

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/13

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/14

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/15

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/16

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/17

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/18

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/19

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/20

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/21

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/22

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/23

 switchport access vlan 99

 switchport mode access

 shutdown

!

interface FastEthernet0/24

 switchport mode access

 shutdown

!

interface GigabitEthernet0/1

 shutdown

!

interface GigabitEthernet0/2

 shutdown

!

interface Vlan1

 no ip address

!

interface Vlan99

 ip address 192.168.1.11 255.255.255.0

!

ip http server

ip http secure-server

!

banner motd ^C Authorized Users Only! ^C

!

line con 0

 password cisco

 logging synchronous

 login

line vty 0 4

 password cisco

 login

line vty 5 15

 password cisco

login

!

end

Switch S2

Building configuration…

 

Current configuration : 1875 bytes

!

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname S2

!

boot-start-marker

boot-end-marker

!

enable secret 5 $1$jTd.$1rhSHu68akU70GYYyc4Dy1

!

no aaa new-model

system mtu routing 1500

!

no ip domain-lookup

!

spanning-tree mode pvst

spanning-tree extend system-id

!

vlan internal allocation policy ascending

!

interface FastEthernet0/1

 switchport trunk native vlan 1000

 switchport mode trunk

!

interface FastEthernet0/2

 shutdown

!

interface FastEthernet0/3

 shutdown

!

interface FastEthernet0/4

 shutdown

!

interface FastEthernet0/5

 shutdown

!

interface FastEthernet0/6

 shutdown

!

interface FastEthernet0/7

 shutdown

!

interface FastEthernet0/8

 shutdown

!

interface FastEthernet0/9

 shutdown

!

interface FastEthernet0/10

 shutdown

!

 interface FastEthernet0/11

 shutdown

!

interface FastEthernet0/12

 shutdown

!

interface FastEthernet0/13

 shutdown

!

interface FastEthernet0/14

 shutdown

!

interface FastEthernet0/15

 shutdown

!

interface FastEthernet0/16

 shutdown

!

interface FastEthernet0/17

 shutdown

!

interface FastEthernet0/18

 switchport access vlan 10

 switchport mode access

!

interface FastEthernet0/19

 shutdown

!

interface FastEthernet0/20

 shutdown

!

interface FastEthernet0/21

 shutdown

!

interface FastEthernet0/22

 shutdown

!

interface FastEthernet0/23

 shutdown

!

interface FastEthernet0/24

 shutdown

!

interface GigabitEthernet0/1

 shutdown

!

Interface GigabitEthernet0/2

 shutdown

!

interface Vlan1

 no ip address

!

interface Vlan99

 ip address 192.168.1.12 255.255.255.0

!

ip http server

ip http secure-server

!

banner motd ^C Authorized Users Only! ^C

!

line con 0

 password cisco

 logging synchronous

 login

line vty 0 4

 password cisco

 login

line vty 5 15

 password cisco

 login

!

end

3 thoughts on “3.4.6 Lab – Configure VLANs and Trunking Answers

  1. You shut down the PC-B interface on S2… It should read f0/2-17, f0/19-24, not f0/2-17, f0/2/18-24 :

    11.Shut down all interfaces that will not be used.

    S1(config)# interface range f0/2-5, f0/7-24, g0/1-2
    S1(config-if-range)# shutdown
     
    S2(config)# interface range f0/2-17, f0/19-24, g0/1-2
    S2(config-if-range)# shutdown

Leave a comment